How to Wallpaper Outside Corners Like a Pro | Perfect Finish Guide
Finishing the edges of a room with wallpaper requires careful attention, especially where walls meet at outside corners. Covering these vertical seams creates a polished, professional look that elevates the entire space. Achieving a crisp, clean line over the corner itself is a skill that transforms a standard paperhanging job into a masterful finish.
Outside corners present a unique challenge because the paper needs to bend around a right angle without creasing or tearing. The goal is to create a seamless transition that hides the raw edge of the paper on both walls. This process relies on precision cutting and gentle manipulation to ensure the design aligns perfectly when wrapped around the protruding edge.
Essential Tools and Material Preparation
Before starting, gather high-quality tools to ensure accuracy and a clean cut. You will need a sharp utility knife, a six-inch metal straightedge, a pencil for marking, and a reliable pair of scissors. Using a rotary cutter can offer greater precision for long, straight cuts compared to a standard knife.
- 6-inch metal ruler or straightedge
- Sharp utility knife or rotary cutter
- Pencil for light marking
- Scissors for trimming paper
- Smoothing brush or plastic smoother
- Clean, dry cloth for blotting
It is crucial to ensure the wall surface is completely dry and dust-free before applying any adhesive. Any debris or moisture trapped behind the paper can cause bubbling or detachment at the critical corner seam. Pre-mixing your paste according to the manufacturer’s instructions and having a damp sponge ready for cleanup will streamline the process significantly.
Measuring and Cutting the Paper
The success of wrapping an outside corner hinges on the initial cut. Measure the height of the wall, adding an extra two inches to the total length to allow for trimming at the ceiling and baseboard. Mark this expanded measurement lightly on the back of the paper to guide your cut.
When you position the paper on the corner, the edge of the sheet should align with the outermost edge of the corner. Use your straightedge to create a vertical score cut precisely along the thickness of the wall. This cut allows the paper to fold flat against both walls without buckling, creating a tight seam that follows the contour of the architecture.
The Folding and Booking Technique
Once the paper is scored, you must fold it back on itself to create a manageable panel. Press firmly along the score line with the edge of the ruler to ensure a clean crease. Fold the two flaps inward so they lie flat against one another, creating a book-like configuration where the corner section is sandwiched in the middle.
Letting the "book" sit for a minute or two allows the paper to relax and makes the final unfolding step easier. When you unfold the paper, you will see a distinct V-shape where the back layer of paper has been removed. This window removes the excess bulk, enabling the remaining paper to bend smoothly around the outside edge without creating a bulge or a ridge.
Application and Seam Alignment
Paste the back section of the paper (the part that will adhere to the wall) and carefully book it again. Align the unfolded V-shaped section with the outside corner of the wall, ensuring the design pattern runs straight down the length of the seam. Slowly unfold each side, pressing the paper firmly against the wall to eliminate air pockets.
| Step | Action | Purpose |
|---|---|---|
| 1 | Position paper flush with corner edge | Ensures pattern alignment |
| 2 | Score the thickness of the wall | Creates a fold line |
| 3 | Book the paper and remove back section | Reduces bulk for tight bend |
| 4 | Smooth paper outward from corner | Eliminates trapped air |
Use a smoothing tool to gently press the paper into the corner, working from the center outward. A slight overhang is beneficial at this stage; you can always trim the excess later. Avoid stretching the paper too tightly, as this can cause the material to contract and pull away from the wall once dry.
Trimming and Final Touches
After the paper is set in place, use your sharp utility knife or scissors to trim the excess material. For the top edge, snap the paper lightly against the ceiling line and cut along the resulting crease for a perfectly horizontal cut. For the bottom, trim along the baseboard line, leaving a small scrap that can be folded behind the board for a secure hold.
Finally, run a dry cloth over the finished corner to absorb any residual adhesive and ensure the seam is lying flat. If the paper pattern features a distinct texture, such as a grass cloth or flock, gently run your fingers down the seam to align the fibers. Taking these final moments seriously ensures the corner looks flawless from every angle.