how to find studs behind shiplap

How to Find Studs Behind Shiplap: A Step-by-Step Guide

By
AD

Removing shiplap to access the wall behind is rarely an option when you are trying to hang a heavy television, anchor a robust piece of furniture, or secure trim. Fortunately, finding the studs hiding beneath those horizontal planks is a precise skill you can master. By combining a few simple tools with a methodical approach, you can pinpoint the vertical wooden supports behind the cladding to ensure your projects are safe and secure.

Why Finding Studs Under Shiplap Matters

The primary reason to locate these supports is load-bearing capacity. Drywall or shiplap alone cannot hold the weight of a large TV, leading to sagging or, worse, a dangerous collapse. Furthermore, many building codes require fasteners to be secured into wood rather than just the drywall substrate. Whether you are installing shelves, mounting hardware, or running electrical conduit, knowing how to find studs behind shiplap saves you from future repairs and gives you confidence in the durability of your installation.

Tools You Will Need

You do not need a professional contractor’s kit to succeed, but having the right tools makes the process significantly faster and more accurate. A quality stud finder with advanced sensors can detect changes in density or the fasteners themselves. Alternatively, a powerful magnet can reveal the location of the screws or nails holding the shiplap in place. For verification, a thin nail and a hammer provide tactile confirmation by physically tapping through the gaps to feel solid wood.

AD
Do You Need Drywall Or Can You Install Shiplap Over Studs? All The Details!
Do You Need Drywall Or Can You Install Shiplap Over Studs? All The Details!
Locating and Marking Your Studs for Shiplap Installation
Locating and Marking Your Studs for Shiplap Installation
How to find a stud without a stud finder
How to find a stud without a stud finder
  • Stud finder (preferred)
  • Strong neodymium magnets
  • Hammer and thin nail
  • Tape measure
  • Pencil

Method 1: Using a Stud Finder

A modern stud finder is the most efficient way to navigate behind shiplap. These devices detect the density changes between the empty air of the wall cavity and the mass of the wood. To use this tool effectively, calibrate it on the adjacent section of wall where there is no shiplap, if possible. Slowly slide the sensor horizontally across the shiplap surface; the device will typically beep or flash when it crosses the edge of a vertical stud. Because the cladding can sometimes confuse the readings, it is wise to mark the suspected location and then verify it with a secondary method.

Interpreting the Readings

Most central support structures are spaced 16 or 24 inches apart, measured from the center of one stud to the next. If your initial discovery aligns with this standard dimension, your accuracy is likely high. Take multiple readings across the length of the wall; this helps you distinguish between the dense edge of one board and the actual framing beneath. Mark the centers of the detected masses clearly so you know exactly where to drive your screws.

How to Install Shiplap - arinsolangeathome
How to Install Shiplap - arinsolangeathome
6 ways to find a stud WITHOUT a stud finder! 🔨
6 ways to find a stud WITHOUT a stud finder! 🔨
10 Ways to Find a Stud in the Wall
10 Ways to Find a Stud in the Wall

Method 2: The Magnet Technique

If you prefer a low-tech solution or do not have a stud finder, magnets offer a reliable alternative. This method works by locating the screws or nails that secure the shiplap to the underlying stud. Run a strong magnet slowly along the seams and raised edges of the planks. You will feel a distinct pull when the magnet approaches the metal fastener hidden just beneath the wood surface. Once you find the magnetic attraction, draw a vertical line downward; the center of that fastener is usually very close to the edge of the stud.

Following the Vertical Line

Since the fasteners are usually aligned with the vertical framing, drawing a straight line down from the screw location will guide you to the general area of the wood support. Use a tape measure to maintain consistent spacing if you are locating multiple studs. This visual guide is invaluable when you begin drilling, as it ensures your anchor screws hit the dense wood rather than the empty cavity.

AD

Method 3: Physical Probing

When electronic tools fail or you distrust their accuracy, the tactile method provides definitive proof. Find the seam between two shiplap boards where the gap is visible. Take a thin nail and gently tap it with a hammer through the small gap at the top of the plank. If the nail sinks easily, you have hit the soft drywall or insulation cavity. However, if the nail meets resistance and stops advancing, you have struck solid wood, indicating the edge of a stud. Mark this spot and move horizontally to confirm the boundaries of the support.

Easy DIY Vertical Shiplap Wall - Angela Marie Made
Easy DIY Vertical Shiplap Wall - Angela Marie Made
Shiplap a Wall: 7 Easy Steps (No Nail Gun!)
Shiplap a Wall: 7 Easy Steps (No Nail Gun!)
5 Ways To Find Wall Studs Without A Stud Finder
5 Ways To Find Wall Studs Without A Stud Finder
the words how to find wall studs even if you don't have a stud finder
the words how to find wall studs even if you don't have a stud finder
Stud Verifier for Drywall
Stud Verifier for Drywall
How to Get Started with Vertical Shiplap in Your Home
How to Get Started with Vertical Shiplap in Your Home

Verification and Standard Spacing

Regardless of the technique you use, always verify your findings by checking for the standard spacing of 16 or 24 inches. Once you are confident in the location of one stud, measure horizontally to locate the others. Consistent spacing is the industry standard for residential construction, so leveraging this pattern ensures you do not miss a hidden support. Double-check your measurements before driving any heavy-duty anchors to guarantee a safe and secure result.

the bathroom is painted in blue and white with text overlay that reads how to install shiplap vertically
the bathroom is painted in blue and white with text overlay that reads how to install shiplap vertically
How to Install Vertical Shiplap: Panels vs. Boards - Stefana Silber
How to Install Vertical Shiplap: Panels vs. Boards - Stefana Silber
10 Ways to Find a Stud in the Wall
10 Ways to Find a Stud in the Wall
How to DIY Make & Install Vertical Shiplap (Tutorial) - Building Our Rez
How to DIY Make & Install Vertical Shiplap (Tutorial) - Building Our Rez
How to Hang Shiplap: Best Easy Tips for Beginners
How to Hang Shiplap: Best Easy Tips for Beginners
Easy DIY Vertical Shiplap Wall - Shortcuts + Tips! Lemon Thistle
Easy DIY Vertical Shiplap Wall - Shortcuts + Tips! Lemon Thistle
Plum Pretty Decor & Design Co.DIY: Faux Shiplap Wall —
Plum Pretty Decor & Design Co.DIY: Faux Shiplap Wall —
8 Foolproof Ways to Find Wall Studs — Even Without a Stud Finder — Good Housekeeping
8 Foolproof Ways to Find Wall Studs — Even Without a Stud Finder — Good Housekeeping
How To Build a Shelf Between Studs
How To Build a Shelf Between Studs
4 Different Ways To Find a Stud in a Wall
4 Different Ways To Find a Stud in a Wall
a man is working on an electrical outlet in the wall with a screwdriver
a man is working on an electrical outlet in the wall with a screwdriver
DIY Shiplap Accent Wall Installation Guide
DIY Shiplap Accent Wall Installation Guide
How to Install Faux Shiplap Paneling in Your Bedroom: Easy DIY Tutorial for Beginners
How to Install Faux Shiplap Paneling in Your Bedroom: Easy DIY Tutorial for Beginners
How Far Apart Are Studs in a Wall?
How Far Apart Are Studs in a Wall?
AD