How to Drain and Remove a Toilet: Step-by-Step Guide
Removing a toilet is often perceived as a daunting household task, but with the right preparation and methodology, it becomes a straightforward project for any DIY enthusiast. Whether you are upgrading your bathroom fixtures, renovating the space, or addressing a stubborn wax ring leak, understanding how to properly drain and remove a toilet is essential. This process requires patience, the correct tools, and a methodical approach to avoid water damage and ensure a clean installation for the new unit.
Gathering Essential Tools and Materials
Before turning the water supply, it is crucial to assemble all necessary equipment to streamline the process. Working efficiently minimizes the risk of accidents and water spills. Having everything within reach prevents mid-project trips to the hardware store, saving both time and frustration.
- Adjustable wrench or channel-lock pliers
- Screwdriver (flathead and Phillips)
- Bucket or large basin
- Rubber gloves and old rags
- Putty knife or chisel
- Flashlight
- Utility knife
- New wax ring and bolts (for reinstallation)
Turning Off the Water Supply
The first active step in the procedure is to halt the water flow. Locate the small angle-stop valve positioned behind the toilet, usually within six inches of the tank. Turn the valve clockwise firmly until it stops; if it is stiff, applying steady pressure with a wrench may be necessary. Flush the toilet to drain the remaining water from the tank and bowl, then use a sponge or towel to absorb any leftover moisture in the basin.
Dealing with a Non-Stop Valve
In older homes or situations where the angle-stop is frozen or missing, you must shut off the main water supply to the house. Locate the main water valve, typically near the water heater or where the main line enters the structure. After turning off the mains, open the lowest faucet in the house to relieve pressure and drain the lines partially. This step ensures that no residual water remains in the pipes leading to the toilet.
Draining the Tank and Bowl
With the water supply secured, you must eliminate the remaining water from the internal components. Hold the flush lever to empty the tank completely. To remove the water from the curved trapway beneath the bowl, use the bucket to catch and hold the residual liquid. If the bowl is full and difficult to hold, use a small cup or dipper to transfer the water to the bucket until the bowl is empty and stable.
Removing the Tank Components
Unsophisticated tanks can hold several gallons of residual water if not handled correctly. Before unbolting the tank, disconnect the supply line connecting the tank to the wall valve. Use the adjustable wrench to loosen the coupling nut carefully, being prepared for a small splash. Once detached, place the line aside and proceed to remove the tank lid gently, setting it aside on a soft surface to prevent chipping.
Unbolting and Removing the Toilet
With the tank water removed, you can now address the securing bolts that anchor the toilet to the floor. These bolts are usually hidden under plastic caps at the base of the unit. Use the screwdriver to pry off the caps and the wrench to loosen the nuts. If the bolts are rusted or stripped, apply a penetrating lubricant and allow it to sit before attempting removal again. Once the bolts are free, grasp the toilet firmly and rock it gently side to side to break the seal of the wax ring before lifting it straight up and off the flange.
Addressing the Wax Ring and Flange
After removal, you will see the old wax ring stuck to the bottom of the toilet and a residual ring on the flange in the floor. Inspect the flange for any cracks or damage; a damaged flange will prevent a proper seal for the new unit. Use the putty knife to scrape away the old wax completely, ensuring a clean surface. This is the perfect opportunity to check the stability of the flange and replace it if necessary to avoid future leaks.
Preparing for Installation
With the toilet removed and the flange cleaned, you can now prepare for the installation of the new unit or verify the area is ready for reinstallation. Measure the rough-in distance—the space from the wall to the center of the flange—to ensure the new toilet fits correctly. Place the new wax ring onto the flange, aligning the bolts, and lower the new toilet onto the ring, pressing firmly to create a secure seal. Reattach the bolts and tighten them evenly, being careful not to overtighten, which could crack the porcelain.