How to Drain a Hot Springs Hot Tub: Simple Step-by-Step Guide
Draining a hot springs hot tub is a fundamental maintenance task that every owner should master. While the process may seem straightforward, doing it correctly protects your equipment and ensures the longevity of your investment. Improper drainage can lead to mineral buildup, damage to the pump, and even voided warranties. This guide walks you through the essential steps, safety protocols, and best practices to drain your spa efficiently and safely.
Preparing for the Drain
Before you even touch a valve, preparation is key to a smooth operation. You need to gather the right tools and choose the right location for the wastewater. Rushing this phase can result in a messy situation or incomplete cleaning, requiring you to start over.
Necessary Tools and Safety Gear
You will need a few critical items to drain your hot springs hot tub effectively. Garden hoses are essential for directing water away from the home’s foundation. A submersible pump can significantly speed up the process if a drain plug is not available. Because you will be handling chemicals and acidic water, waterproof gloves and safety goggles are non-negotiable. Additionally, having a shop towel or mop on hand helps manage any spills during the disconnect process.
Checking Chemical Levels
Prior to draining, you should test the water’s chemical balance. While you are about to discard the water, this is a final opportunity to ensure the chemistry is stable. If the water has been treated with high levels of bromine or chlorine, you must allow the levels to drop to safe concentrations before release. Never drain water that has been recently shocked or treated with algaecides, as this can harm local foliage and drainage systems.
The Drain Process: Step by Step
With prep work complete, you can initiate the physical draining of the unit. The method you use depends on whether your hot springs hot tub has a low-voltage drain plug or relies on a manual pump system. Following the sequence below prevents airlocks and ensures the tub empties fully.
| Step | Action | Purpose |
|---|---|---|
| 1 | Turn off power at the circuit breaker. | Safety to prevent electrical shock. |
| 2 | Open the drain plug or attach a submersible pump. | Initiate water removal. |
| 3 | Disconnect the water supplies if applicable. | Prevent backflow or pressure issues. |
| 4 | Allow gravity to pull water from the lines. | Ensure complete emptying of pipes. |
Utilizing the Drain Plug
If your hot springs hot tub is relatively new or professionally installed, it likely features a low-voltage drain plug located at the base of the unit. This is the most efficient method and usually requires nothing more than a standard garden hose. Locate the plug, twist it counter-clockwise, and allow the water to flow directly into a drainage area or a portable tank.
Dealing with Pumps and Low-Lying Units
For models without a dedicated drain plug, or for installations where the tub sits below the exterior drainage point, a submersible pump is the ideal solution. Place the pump at the lowest point of the tub basin. Connect a hose to the pump outlet and route the water to a safe exit point. This method requires a bit more setup but is highly effective for ensuring every last drop is removed, preventing stagnant water that can breed bacteria.
Post-Drain Procedures
Once the visible water is gone, the work is not complete. The lines and internal components still hold significant moisture that can lead to mold or freezing damage. Taking the time to purge these systems is just as important as the initial drain itself.
Clearing the Lines and Air Chamber
After the tub is empty, you should open the air induction valves and turn the power back on briefly for the pump. This creates a suction force that pulls residual water out of the internal plumbing. You will hear the gurgling of water moving through the lines until they are clear. For freezing climates, it is vital to blow out the lines with compressed air to prevent pipes from bursting during winter weather.
Cleaning the Basin
With the structure empty and dry, you can now address the interior surface. Use a soft brush and a mixture of water and vinegar to scrub away any biofilm or residue that has accumulated. This is the perfect time to inspect the acrylic or metal shell for cracks, leaks, or discoloration. Allowing the tub to air dry completely with the cover off ensures that no moisture remains to dilute the protective coatings or sealants used during manufacturing.